View and Download KAWASAKI NINJA ZX service manual online. ZZR ZZR ABS Ninja ZX Motorcycle Service Manual. JKBZXT40AAA ZXT40A JKBZXT40ABA ZXB6F ZXT40B EvilTwin’s Avatar. Join Date: Oct Location: Orange, CA. Posts: 5, I Ride : Versys. Kawasaki ZX and ZZR Service Manual. Tue, 20 Nov GMT kawasaki zx14 zx pdf – View and. Download KAWASAKI. NINJA ZX service manual online. NINJA. ZX

Author: Moogusida Dijar
Country: Netherlands
Language: English (Spanish)
Genre: Life
Published (Last): 21 September 2009
Pages: 75
PDF File Size: 7.29 Mb
ePub File Size: 7.58 Mb
ISBN: 912-9-24965-776-8
Downloads: 45243
Price: Free* [*Free Regsitration Required]
Uploader: Kazizuru

Only put the heat insulation rubber plate on the cylinder head cover.

Owner’s & Service Manual | Kawasaki Vehicle Manuals

Your answer needs to include more details to help people. Lubri- cation points are called out throughout this manual, apply the specific oil or grease as specified.

Dec 30, Yamaha Motorcycles.

Follow the specified tightening sequence. Clutch Master Cylinder Disassembly Measure the clearance with engine cold. Air Cleaner Drain Hose 2.

KAWASAKI NINJA ZX-14 Service Manual

Idle Adjusting Screw 2. Wait until it cools down. Balance Weight Installation 30 g 1.

Service Code 51 Stick Coil 2: If the fan does not rotate, the fan motor is defective and must be replaced. For more information about your issue and valuable “FREE” downloads that you will need please click mannual the links below.

The email address entered is already associated to an account. Seat Cover Equipped Models. Dec 30, Motorcycles.


Water Temperature Sensor 2. Apply silicone sealant to the circumference of the alter- nator lead grommet, and fit the grommet into the notch of the cover securely. Main Fuse 30 A 4.

Apply molybdenum disulfide grease. Throttle Body Assy 5. If the camshaft journal diameter is less than the service limit, replace the camshaft with a new one and measure the clearance again.

Seat Height mm If any plates show signs of damage, or if they have worn past the service limit, replace them with new ones. Bracket for Separator Starter Lockout Switch 5. Lately during the filling cycle water hammer is occurring.

If the display function does not work, replace the meter assembly. Such a shock to the relay can damage it. Data is transmitted from the two nodes-the ECU and meter unit-on the Mqnual bus and does not contain specific bus addresses of either node. Headlight Relay High 2.

2006 Kawasaki Ninja ZX-14 — Owner’s Manual

If the commutator diameter is less than the service limit, replace the starter motor with a new one. Crankshaft Sensor — 6. Forcibly prying off the seal cap to add water is very dangerous. Please assign mabual manual to a product: Turn the ignition switch OFF. Ball Bearing and Needle Bearing Do not remove pressed ball or needle unless removal is absolutely kawasaik. The manuxl history can be referred using the KDS Kawasaki Diagnostic System when solving unstable problems Much of the DFI system troubleshooting work consists of confirming continuity of the wiring.


Apply grease to the threads. If they are damaged, replace them. If the surface is corroded or if the blades are damaged, replace the water pump assy. By pressing ‘print’ button you will print only current page. Joint Connector 2 Sidestand Switch Lead 5. Jan 10, kawasaki Ninja ZX Apply the oil to the O-rings so that the O-rings will be coated with oil.

Fuel Pump Relay 4. Page FUEL SYSTEM DFI Self-Diagnosis Service Code Table Service Code Problems Main throttle sensor malfunction, wiring open or short Inlet air pressure sensor malfunction, wiring open or short Inlet air temperature sensor malfunction, wiring open or short Water temperature sensor malfunction, wiring open or short Atmospheric pressure sensor malfunction, wiring open or short Crankshaft sensor malfunction, wiring open or short Camshaft position sensor malfunction, wiring open or short Spacer, Swingarm Pivot Nut Wrench: If the spring of either fork leg is shorter than the service limit, it must be replaced.

Subthrottle Valve Actuator 7. Special Tools – Bearing Puller [B]: Pilot Screw Adjuster, C: