n Light Weight. For footnotes refer to the last page. IRHM REF: MIL-PRF- / TOAA. This datasheet has been downloaded. 2N 2NU. JANSR (K RAD(Si)). JANSF (K RAD(Si)). ABSOLUTE MAXIMUM RATINGS (TC = +25°C unless otherwise noted). Parameters / Test. 2N datasheet, 2N pdf, 2N data sheet, datasheet, data sheet, pdf, Microsemi, N-Channel.
|Published (Last):||10 December 2011|
|PDF File Size:||12.39 Mb|
|ePub File Size:||13.49 Mb|
|Price:||Free* [*Free Regsitration Required]|
2N Datasheet – MOSFETs and TempFETs from International Rectifier
The wire type is 05, gold plated; 0. Ferrites can be pressed in block form and then machined into intricate shapes. When specified, under-plating shall be in accordance with 5 2 1. This note prohibits the use of pure unalloyed tin finish on all surfaces. The lead finish vatasheet restrictions on datasehet case material are defined in the following paragraphs of the SCD: The line make inductors consist of the following parts: Complete back wall coverage is optional.
The thickness shall be to microinches Mil-M defines finish A as hot solder dip. Use of tin plating is prohibited as a final finish and as an undercoat see 6 8.
Without sacrificing magnetic properties, many operations can be performed on ferrites, while maintaining strict dimensional datasheey mechanical tolerances: Description Part Value 1. Use of tin plating is prohibited see 6. Consists of the tetter M. Mag netics also ofTers unique capabilities in the design and dqtasheet of spedalized components fabricated from magnetic materials in many sires and shapes. H – Copper-aluminum -si hcon-cobalt alloy alloy. The type will be defined on the specification sheet.
Where space is critical, the low profile CLP component should be considered, but at the expense of some reduction in electrical Q. Capacitors covered by this specification are classified by style as specified see 3 1 1. Dle ana tons Is inches unlees atherwlae specified.
I SEM anomalies if applicable. Magnetics No Yes 3. Send comments regarding this burden estimate or any other aspect of this collection dataeheet information, including suggestions for reducing this burden, to Washington Headquarters Services, Directorate for Information Operations and Reports, Jefferson Davis Highway, SuiteArlington, VAand to the Office of Management and Budget, Paperwork Reduction ProjectWashington, DC Zinm cadmium or pure tin shall not be used as a datasheett material.
Use of tin- lead Sn-Pb finishes are acceptable provided that the minimum lead content is 3 percent. Lead freiaa or terminal Material end finish ahet. Use of tin-lead Sn-Pb finishes are acceptable provided that minimum lead content is 3 percent. Tin-coated copper wire shall conform to FT n-coated, tof i or annealed copper wire in accordance with AST Use of tm-lead finishes are acceptable provided that the minimum lead content is 3 percent.
Commonly used sizes ore in stock for immediate shipment. AD core sizes ran be provided in non- metallic phenolic or plasticaluminum, or CVB Guaranteed Voltage Breakdown coated aluminum boxes. ASTM F30 see 5. The device type Tkwber shall be es specified in the associated detail spec l f Ication or SO the numbers Shall consist o’ two digits atsiprwd saquant ially, froa 01 to W within each associatad detail specification or SMC.
The type will be defined on the specif lcet Ion sheet. Materials and Manufacture 4. Silver-coated copp er-cl a d steel wire. The materials and coatings Shill be it specified f toe 3.
Use of tin plating is prohibited as a final finish and as an undercoat see 6. The matte-tin plating shall contain no more than 0 05 percent by weight codeposiled organic material measured as elemental carbon Minimum lead content shall be 3 percent.
The manufacturer may have a pure tin finish plating that is used on some product. MIL-CE does not specify the lead finish, but it does prohibit the use of a pure tin finish. The device type matter shell be at specified In the auaclated detail apacif ieatl on or M. For glass- to -metal sealed products, all devices with terminals which are solder dipped to the seal shall pass screen 7 of table IV.
The P IN shell be as shown in the following exaaple: Summary by part number with the quantity used per assembly for the electrical components.
【2N7269 IR】Electronic Components In Stock Suppliers in 2018【Price】【Datasheet PDF】USA
Length jt controls the operating frequency. SM – I9B2 J. Annoaltd copper-clad aluminum wire. MIL-T does not contain a statement prohibiting the use of tin platting.
Component List  page :: Oxygen Electronics, LLC
Lab Par wsc Typa: C – Hot solder dipped 60 microinch minimum. Search the history of over billion web pages on the Internet. Dimensions in inches taxless otherwise specified. Parts that define the plating finish in their procurement specification, but do not specifically prohibit the use datawheet a pure tin finish.