HP / Hewlett Packard / Agilent Used A Autoranging System Power Supplies, Refurbished – A, A, A, A, A, A, A- Used Test. 19 results Here you will find a large selection of new and used Keysight Technologies ( Agilent HP) A listed at special prices. Although some items match. Find great deals for Hp/agilent A System Autoranging DC Power Supply v 17a. Shop with confidence on eBay!.
|Published (Last):||11 August 2011|
|PDF File Size:||17.77 Mb|
|ePub File Size:||16.4 Mb|
|Price:||Free* [*Free Regsitration Required]|
A conventional power supply subsystem capable of monitoring and controlling power supply voltage and current agolent a variety of hardware in addition to the actual supply.
Fewer instruments mean less rack space, easier calculation of system specifications, quicker configurations, higher system reliability, more rapid troubleshooting, and simpler software. As autoranging power supplies, these models can provide a wide and continuous range of voltage and current combinations at the maximum rated power.
Hp/agilent 6030A System Autoranging DC Power Supply 200v 17a
This often allows both present and future requirements to be satisfied with fewer supplies, also reducing the number of instruments in the system.
Most of the extensive programmable instruction set can be simulated with front panel controls, thus facilitating design and debugging of system hardware and software.
During system operation, if local control is not needed, the front panel controls can be disabled with a computer command. If operator interaction is required, a computer command can place limits on the output voltage and current available. Often, control and monitoring via the front panel is very useful during system development, but not needed afterwards.
If the system is reproduced without further development, power supplies without front panel controls and meters Option can then be used except HPA. Ordering your power supplies with Option significantly decreases the cost.
Because of the delicate nature of most loads, these system power supplies provide several different types of protection. If reaching a programmed value indicates an undesirable condition, the power supply can be instructed to automatically down-program the zero output. For example, if the programmed current limit is reached while testing a PC board assembly, it may indicate a shorted component. In this case, the FOLDBACK feature, if enabled, would be able to serve as an over-current protection circuit and down-program the power supply automatically.
The built-in overvoltage protection circuit is adjustable with a front panel control. The set trip level can be displayed on the front panel meter and also can be read back over the HP-IB, thus making adjusting the level easy.
Production procedures sometimes require the operator to adjust the output voltage or current of a power supply locally with the front panel controls. If this is done, programmed levels can be set to limit the available adjustment range to a safe margin. Potentially harmful conditions, such as overtemperature and high or low ac input, will trigger the power supply to automatically down-program to zero output.
This status can also be read back to the computer over the HP-IB and can be used to generate interrupts.
Up to 16 power supplies can share one HP-IB address, while still providing full independent control, when connected with a modular telephone-style cable. This feature requires programming in TMSL mode.
To use this feature, you will also need to order a serial link cable for each unit to be added to the chain, with the first unit connected directly to HP-IB. The standard serial link cable is 2 meters 6.
If your application requires more power than the output capability of a single unit, you can use an auto-series connection for greater output voltage or an auto-parallel connection for greater output current. Remote sensing can be used to maintain the CV load effect specification at the load with up to 0.
Operation is possible with up to 2. Analog programming inputs and monitoring terminals are provided on the rear panel in addition to the HP-IB programming capabilities.
6030A System Autoranging DC Power Supply, 200V, 17A
Zero to full scale voltage or current can be programmed with either volt voltage signals, or ohm resistance avilent. The monitoring terminals present volt buffered signals which are proportional to the output voltage and current.
A special modification is available for HP models A, A and 6030s to ensure stable operation when operating into inductive loads up to 10 H. View Cart My Account. This applies to HP A and A only. Please Call Rack mount kit for single unit. Front Panel Control Protection Features.
Keysight Technologies (Agilent HP) A used or new for sale at used-line
Programmable Features System Configuration. Rack mount kit for two units side by side. Rack mount kit for single unit.
A blank filler panel is supplied when this option is ordered with HP A and A.