BU datasheet, BU pdf, BU data sheet, datasheet, data sheet, pdf, Central Semiconductor, Leaded Power Transistor General Purpose. BU datasheet, BU circuit, BU data sheet: MOSPEC – POWER TRANSISTORS(A,V,55W),alldatasheet, datasheet, Datasheet search. BU Bipolar Transistors – BJT are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for BU Bipolar Transistors – BJT.

Author: Kajira Akinozshura
Country: Denmark
Language: English (Spanish)
Genre: Literature
Published (Last): 7 December 2006
Pages: 171
PDF File Size: 19.74 Mb
ePub File Size: 1.16 Mb
ISBN: 874-1-88761-648-6
Downloads: 28289
Price: Free* [*Free Regsitration Required]
Uploader: Arashirg

Like most logic circuits of this type setting-up is tedious rather than difficult. The screen supply is now ready for service.

catasheet In our example, this coefficient is equal to:. The description refers to one channel, which is Channel B the right-hand channel looking at the circuit diagram.

NPN Si Transistor, Horizontal Deflection – NTE

Here are few examples: Maximum power rating for a transistor, is PCmax found in a datasheet. High voltage Posted by darshelectro in forum: The screen supply overvoltage alarm thresholds should be set by means of RV4 and RV5 so that the alarms operate at about V; similarly, the screen undervoltage alarms should set via RV1 and RV2 to operate at about V. Part 1 – Part2.

The raw input – which should be V or above – is fed via the optoisolator IC4b, whose function was discussed earlier, to the collector of TR8. The number following the letter is of no importance to users.

The cheapest bu08 is to use BU television line output transistors for TR and these will work well even though the hk of datawheet BUs has been found to be very low. As a helpful guide, there is a chart in this chapter which shows a list of replacements for some frequently used transistors.


If D48 and R68 are omitted and link 1 fitted, leaving pin 72 open-circuit corresponds to the transmit condition.

BU 데이터시트(PDF) – Siemens Semiconductor Group

The gain is equal to:. Oct 18, 3. Oscillator to test transistors To test PNP transistors, same would go, only the transistor which would need to be replaced is the T1, and the battery, LED, C1 and C2 should be reversed.

You May Also Like: Almost nothing else in amateur radio is as important as this rule, and there are absolutely no exceptions to it. Placement of leads and different housing types for some commonly used transistors are in diagram 4. The performance of this supply is also good. In a series of some 20 test flashovers, datasjeet were induced by tuning and loading a W1SL-type MHz amplifier with these modifications incorporated for full output power into a dummy load, removing the load and applying full drive, there was no damage to any part of the amplifier or its power supply apart from blown fuses in the ehv supply and normal operation could be resumed as soon as the fuses had been replaced and the load had been reconnected.

The second stage should divide the output of the first down to the required voltage. Feb 20, 2, If the pot is turned fully, the base voltage will increase slightly to about 0. The LED will blink when a good transistor is fitted datasheer the circuit.

They datawheet current driven by pulse transformer. Variable capacitor C and coil L form a parallel oscillating circuit which is used to pick out the signal of a radio station out of many different signals of different frequencies.

Home – Techniek – Electronica – Radiotechniek – Radio amateur bladen – Radio Communication – A power supply and control system for tetrode amplifiers 2 Screen grid supply Refer now to Fig 2, datasheeg is a dual-channel screen supply capable of producing a regulated or V for Class AB I and Class C use respectively and which will source and sink some 30mA; it is a development of the design published in III.


Connect a voltmeter to the output of channel B pin The authors suspect that several other tv line output or smps transistors could be used in satasheet part of the circuit, although they have not been tried.

New Jersey Semiconductor

Any dataseet with a Vdss rating in excess of about V and a current datashete of an amp or so should work well, although minor component changes need to be made. These are general purpose transistors. The inductor is formed by winding about 10 turns of 22swg enamelled wire around the body of a low-value 2W resistor.

Nov 18, 1, As we previously said, many electronic devices work perfectly even if the transistor is replaced with a similar device.

All you need is an option on your multimeter for measuring DC current up to 5mA. As far as the control logic is concerned, setting-up is a matter of systematically checking that all alarms operate, that the main timer and audible alarm timer work, and that the “ready” relay operates when all supplies have been established.

There are various devices which can be used in this design. In this case the transistors have a metal plate with hole, which is used to attach it to a heat-sink to allow the heat to be passed to a larger surface.