CU320 MANUAL PDF

SINAMICS S Equipment Manual for Booksize Power. Units. • SINAMICS S Equipment Manual for Description of the LED states of a CU SINAMICS S Equipment Manual for Booksize Power Units .. CU DP from firmware version with integrated Ethernet interface. ○ Smart Line. Siemens SINAMICS S Manual Online: Control Unit (cu), Description, Safety Information. Control Unit (CU) Description The CU

Author: Voodootaxe Voodookus
Country: South Sudan
Language: English (Spanish)
Genre: Literature
Published (Last): 26 June 2017
Pages: 474
PDF File Size: 17.22 Mb
ePub File Size: 18.70 Mb
ISBN: 165-3-72944-610-9
Downloads: 3074
Price: Free* [*Free Regsitration Required]
Uploader: Salar

If necessary, you can request the support of your local Siemens office. Connect the cable to terminals -X5.

CU320 Support

All units and components except for chassis format. A mains rectifier, a voltage-source DC link and an inverter for supplying a motor are integrated in the Power Module. Are the cables connected to the terminal block of the screen connecting plate?

Cabinet units must not be disassembled while still on wooden pallets and awaiting transport. Camera And Recordings The remaining computation time is displayed cu20 parameter r[2]. If a sufficient clearance cannot be maintained, you must install additional shields.

CU and BOP20 c320. Send My Number Note Refer to the order documentation e. The measurements may only be carried out by properly trained specialist personnel. The maximum loadcarrying capacity of a Faston connection point is 20 A. For this reason, the unit should not be opened until a reasonable period of time has elapsed.

Siemens SINAMICS S Specifications |

The cabinet units are packaged by the manufacturer in accordance with the climatic conditions and stresses encountered during transit and in the recipient country. The details in the catalogs and proposals also apply to the design of special equipment versions.

  LESLIE MARMON SILKO YELLOW WOMAN PDF

If the downtime is longer than 2 years, the capacitors must be reformed as described in the chapter titled “Maintenance and servicing”, section “Reforming the DC link capacitors” in this mnual. Raise The msnual are dependent on the actual display and are used to raise or lower values. For all cabinet units, the busbar is a 60 x 10 mm nickel-plated bar. Actual customer verification of the license for the software that is subject to license is called a certificate of license.

Only approximately 10 mm of insulation should be stripped. The positions of the fixing screws are indicated by red markings on the outside of the pallets.

Death, serious injury, or substantial material damage can result if these guidelines are not observed. Cable routing for the “Safe Torque Off” and “Safe Stop 1” functions Note The procedure is the same as that for the customer terminal block.

Table 3- 2 Quantity 4x Content of the accessories kit and recommended fixing points Connectors Row clamps incl. C Is light bright if at least one parameter was changed and the calculation for consistent data management has still not been initiated. Adjustable speed electrical power drive systems Part 5: Measuring system — Which measuring system is being used?

Ir A Url Locate the BOP20 3. The units in blocksize format are optimized for single-axis applications. Caution If two power transistors in the power unit one in the upper and one in the lower bridge fail at the same time, this can cause a momentary movement.

For Your Safety A Braking Module and braking resistor are required only if the drives need to be decelerated in a controlled manner after a power failure i. The phone runs on the Other operating system OS.

  FOCAL TN44 PDF

Note The plug and connection jumpers are correctly inserted when the plug clicks into place. Cable routing Cable for supply infeed Signal cables Notice: Are all of the prerequisites for commissioning checked and were the points in the checklist for commissioning checked refer to Chapter 2?

Dismantling The transport eyebolts can be unscrewed and removed. Red — Steady light Off Cyclic communication has been interrupted. Guide the cable further up into the cabinet and, when it reaches customer terminal block -X55, guide it to the left or right to -X The selected project is displayed at the top left.

Cingular mall, Shop tones, Shop games | LG CU User Manual | Page 57 / 99

The DC link is supplied from the line voltage by a Line Module. With intelligent compensation of capacitive and inductive reactive currents, SINAMICS S also ensures that no unnecessary power losses occur in the power supply and that no current harmonics occur.

For each cabinet row installed, you must mount one side panel on the right option M26 and one on the left du320 M The CU Control Unit has been designed to control multiple drives. Volumen De Datos Class 1K4 Temperature Manuap value in normal operation is lower. Each monitoring channel triggers the safe pulse disable via its shutdown path.

The parameter for the rated motor mnual p and onwards are appropriately pre-assigned. Inicio De Media Net Quitar La Tarjeta De Memoria