on my Emphaser EAD the relays do not pick up. when i bridge them,amp plays normal sound. Q50,51, are ok what else could. Does anyone know what kind of transistors have in outputs and power supply? I am thinking to buy one with blown outputs and fets. Search among more than user manuals and view them online
|Published (Last):||27 March 2015|
|PDF File Size:||17.93 Mb|
|ePub File Size:||19.96 Mb|
|Price:||Free* [*Free Regsitration Required]|
Wem diese Einstellung zu schwierig ist, kann auch nur mittels umpolen des Subwoofers die generell richtigere Anschlussvariante austesten.
Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. Zum Einsatz kommen z.
Innerhalb der ersten 30 cm nach dem Pluspolklemmenabgriff muss eine Hauptsicherung angebracht werden Absicherung des Pluskabels gegen Kurzschluss auf Fahrzeug-Masse und dadurch resultierendem Kabelbrand! The target is, that both speaker systems, normally separated by aprox. If the LED lights up red, your installation is wrong!
EMPHASER EAD INSTALLATION & OPERATING MANUAL Pdf Download.
Ejphaser contact point where the ground wire is attached to, must be solid and clean, i. Each RCA line-input pair accepts input voltages from mV to 7V, providing a good match with the line-output levels of almost any head-unit on the market. Es sollte ausserdem den selben Querschnitt wie das Pluskabel besitzen.
The ground power wire must have the same cross-section as the positive power cable.
The remote low pass level remote control unit can be mounted in any convenient position where it can be reached while you drive in your car. After installation, there should be a clearance of at least 5cm to all sides including the top of the amplifier heatsink.
EMPHASER EAD Specifications |
Verwenden Sie die beigelegten Gummi-Isolatoren um die Endstufe n von der Fahrzeugmasse isoliert zu montieren. These recommendations guarantee trouble-free operation of your amplifier, giving you full power output. Limited Warranty Dear customer Please read the warranty specifications below carefully.
The low pass level remote control — if installed in ae1800d system configuration – should be set at a low position, so there is enough headroom to turn up the bass volume later on.
Now switch on your head unit. Als Montageort eignet sich z. Es sollte ausserdem den selben Querschnitt wie das Pluskabel besitzen. The ground power wire must have the same cross-section as the positive power cable. The phase-shift control enables you to match the acoustical phase relations of subwoofer and the speaker system playing in the front doors.
As a rule of thumb, settings in a range between 60 to 90 Hz will render best sonic results. Before you attempt ea8100d adjust the lowpass crossover frequency, you must set the subsonic highpass filter to its lowest position 10 Hz. Tighten both power input terminals of the amplifier, and double check for perfect fit of both main cable leads!
EMPHASER EA1800D Manuals
To maximize the performance of this amplifier and your car audio system install, we recommend that you acquaint yourself thoroughly with all capabilities and features of this EMPHASER amplifier.
Limited Warranty Dear customer Please read the warranty specifications below carefully. There must not be a direct contact of the amplifier emhpaser, bottom panel or other metal parts to the vehicle chassis ground!
Only best electrical and electronic components have been used for the assembly of this amplifier line. Consider all additional electrical requirements and accessories, such as power cables, interconnect cables etc. Slowly increase the input gain control of the channel pair, that drives the subwoofer sby turning the Emphader control clockwise until you can just emphasrr hear distorted sounds coming out of your subwoofer system.
The remote low pass level remote control unit can be mounted in any convenient position where it can be reached while you drive in your car. Gehen Sie die gesamten Installationsanweisungen nochmals genau durch. Make sure that there is no wiring harness, fuel tank etc. Close the electrical circuit by inserting the main fuse. After installation, there should be emphsaer clearance of at least 5cm to all sides including the top of the amplifier heatsink.